Honeywell Chronotherm Iv Plus Install Manual
Honeywell Chronotherm Iv Plus Manual added on Thursday, September 13th, 2012 - We are giving you with tools to read online Honeywell Chronotherm Iv Plus Manual pdf document in our site. We use the most popular pdf document viewer called. If you have any problem to read online this Honeywell Chronotherm Iv Plus Manual datasheet note database, we recommended you contact us or report a broken link, and we will take care of it As Soon As Possible! For further inforamtion, about the Honeywell Chronotherm Iv Plus Manual pdf file by clicking on this link.
Installer must be a trained, experienced service 4. After completing installation, use these instructions Location Install the thermostat about 5 ft (1.5m) above the floor in an area with good air circulation at average temperature. Do not install the thermostat where it can be affected by: —. T8601D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS Wallplate Installation The thermostat can be mounted horizontally on the wall or on a 2 in.
Position wallplate horizontally on the wall or on a 2 in. RELAY TEMPERATURE SENSOR Mounting Thermostat (HOT) 1. Engage tabs at the top of the thermostat and wall- TRANSFORMER 2.
Press lower edge of case to close and latch. NOTES: To remove the thermostat from the wall, first pull M10353 HEAT. DECREASE TIME SETTING OR SCROLL BACKWARD THROUGH INSTALLER SETUP AND SYSTEM TEST Fig. T8601D key locations and descriptions. Thermostat System and Fan key locations.
NOTE: Always press the keys with your fingertip or INCREASE TEMPERATURE SET RETURN TIMES. Table 2 and, if no changes are necessary, go to the Installer Self-Test section. The Installer Setup is used to customize the thermostat to specific systems.
Some of the options include temperature display, system changeover and outdoor temperature display. Not used 25 thru 29 Deadband Not used 31 and 32 Minimum off time for the compressor 69-1410—2 Table 3. Thermostat Installer Setup Options. Factory-Setting Display Description — — Conventional application where equipment control fan operation in heat mode —. Review the settings to confirm that they match the system. Press Run Program to exit the Installer Setup.
The thermostat has saved the Installer Setup changes and initiated a reset in order to operate using the new settings. Be sure to set the current day and time immediately. 69-1410—2 4. Press Run Program. Program Viewing or Resetting Timer Settings Set Day/Time When the thermostat activates a timer, the thermostat flashes Filter until the timer resets. Reset the timer by pressing the i key until the Filter. INSTALLER SELF-TEST Use the Installer Self-Test to check the thermostat oper- ation.
Refer to Table 4 for a list of the available self-tests. CAUTION Equipment Damage Hazard. Minimum compressor off-time is bypassed during Installer System Test.
Avoid cycling compressor quickly. T8601D CHRONOTHERM® IV DELUXE PROGRAMMABLE THERMOSTATS THERMOSTAT INFORMATION 1. Press the Time to access the thermostat information. Press the increase! Key to display the production date code.
Honeywell Chronotherm Iv Plus Troubleshooting
Honeywell Chronotherm Iv Plus Reset
The first two large digits are the month and the third digit is the last digit of the year. Heating does No power to the thermostat. Check that C terminal is connected to the system transformer. Thermostat minimum off time is activated. System selection is not set to Heat.
Symptom Possible Cause Cooling does not No power to the thermostat. Check that C terminal is connected to the system transformer. Thermostat minimum off time is activated. System selection is not set to Cool.
Cool setpoint is above room temperature.
• I/O Modules and wiring. • Addresses used in the S7 range of controllers. Siemens advanced s7 training manual. • Using the Simatic S7 programmer to connect online and monitor programs to determine plant problems. Course Content • The hardware architecture of the S7 range of controllers.