John Deere Lt 125 Manual
Operating OMM142698 Issue I0 Lawn Tractors LT133, LT155 and LT166 PIN (125001 - ) Copyright© Deere & Company Operating Daily Operating Checklist o Test safety systems. O Check tire pressure. O Check fuel level. O Check engine oil level.
O Remove grass and debris from machine. O Clean air intake screen. O Check area below machine for leaks. Avoid Damage to Plastic and Painted Surfaces Do not wipe plastic parts unless rinsed first. Insect repellent spray may damage plastic and painted surfaces. Do not spray insect repellent near machine.
Be careful not to spill fuel on machine. Fuel may damage surface.
Wipe up spilled fuel immediately. Operator Station Controls. M63896 Install both springs into front position (C) for softest ride.
Install both springs into rear position (B) for firm ride. Install springs in all four positions (B and C) for the firmest ride. NOTE: Installing all four springs is also recommended for use with the Optional High-Back Seat. Additional springs and the high-back seat are available at your John Deere dealer. Adjusting Cutting Height NOTE: Lift lever should be in transport position before turning cutting height knob. Cutting height can be adjusted from approximately 25-100 mm (1-4 in). When lift lever is in transport position, cutting height is approximately 100 mm (4 in).
Put lift lever in transport position. 48C: 37 Nm (27 lb-ft.) (328 lb-in.) Adjusting Mower Level (Side-to-Side) c CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. Always wear gloves when handling mower blades or working near blades. NOTE: Mower wheels should not contact the ground when leveling the deck. Park machine safely on a level surface.
Inflate tires to the correct pressure. Adjust cutting height to 50 mm (2 in). Put lift lever in mowing position.
NOTE: The difference between blade measurements must not be more than 3 mm (1/8 in). MIF Picture Note: Left side shown. Adjust lift links by turning nut (G) clockwise to raise left side of mower, counterclockwise to lower left side of mower. Adjusting Mower Level (Front-to-Rear) c CAUTION: Avoid injury! Rotating blades are dangerous.
Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. Always wear gloves when handling mower blades or working near blades.
NOTE: Mower wheels should not contact the ground during leveling. Park machine safely on a level surface.
Inflate tires to the correct pressure. Adjust cutting height to 50 mm (2 in). Put lift lever in mowing position. Turn right blade so blade tip points straight forward. MIF c CAUTION: Avoid injury!
Engine exhaust fumes contain carbon monoxide and can cause serious illness or death. Move the vehicle to an outside area before running the engine.
Do not run an engine in an enclosed area without adequate ventilation. Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area. Allow fresh outside air into the work area to clear the exhaust fumes out. Use the following checkout procedure to check for normal operation of machine. If there is a malfunction during one of these procedures, Do not operate machine.
See your John Deere dealer for service. Perform these tests in a clear open area. Keep bystanders away. Testing Mower Engagement Lever Switch 1. Sit on the seat. Lock the park brake.
Result: Park brake must prevent machine from moving. If machine moves, parking brake needs to be adjusted. Testing Reverse Implement Option (RIO) 1. Start engine. Engage mower.
C CAUTION: Avoid injury! Rotating blades are dangerous. Children or bystanders may be injured by runover and rotating blades. Before backing up, carefully check the area around the machine. Look behind the vehicle to be sure there are no bystanders.
Begin reverse travel by depressing reverse foot pedal for Automatic transmission or moving gear shift lever to R (reverse) position for Gear transmission. Push and hold brake pedal (A) down. Pull park brake lever (B) up to lock park brake. Release brake pedal.
Pedal should stay down and park brake lever should stay locked. Unlocking park brake: 1.
Push and hold brake pedal down. Push park brake lever down to unlock park brake. Release brake pedal. Starting Engine c CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death. Move the vehicle to an outside area before running the engine. Do not run an engine in an enclosed area without adequate ventilation.
Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area. Allow fresh outside air into the work area to clear the exhaust fumes out. NOTE: Engine will not start unless mower is disengaged and transmission is in neutral. Push down brake pedal. Check starting conditions. M94336a A - STOP Position B - Headlights `ON' Position C - Run Position D - Start Position Turning Headlights ON/OFF (Engine OFF) ON - Turn key switch to headlights `ON' position (B) - lights will turn on. However, this will drain the battery rapidly, so do not leave headlights on for periods longer than 1 - 2 minutes.
Kobelco excavator service manual [ZHANG FENG SHAN?LIN ZHI BAI] on Amazon.com. *FREE* shipping on qualifying offers. Fri, 26 Oct 2018 15:38:00. GMT shop manual kobelco. 350 pdf - Kobelco sk210 8 acera mark 8 excavator parts catalog, buy kobelco sk210 8 acera mark 8. Link: http://www.dhtauto.com/showthread.php?62918-Kobelco-Shop-Manual&p=64405#post64405. Shop manual kobelco.
OFF - Turn key switch to STOP position (A) - lights will turn off. Turning Headlights ON/OFF (Engine RUNNING) ON - Start engine, then turn key switch from run position (C) to headlights `ON' position (B) - lights will turn on. OFF - Turn key switch from headlights position (B): to run position (C) - lights will turn off and engine will continue to run. To STOP position (A) - lights and engine will turn off. Using Travel Controls on Gear Transmission c CAUTION: Avoid injury! Children or bystanders may be injured by runover and rotating blades. Before traveling forward or rearward: Carefully check the area around the machine.
Disengage the mower before backing up. Push clutch/brake pedal (A) all the way down. NOTE: The engine and mower will stop as the gear shift lever is moved to R (reverse) if the mower engagement lever is not in the off position. Put mower engagement lever (C) in the off position. Look behind the vehicle to be sure there are no bystanders nearby.
Move shift lever (B) to R (reverse) position. Release clutch/brake pedal slowly. To stop travel: Push down clutch/brake pedal. Using Travel Pedals on Automatic Transmission c CAUTION: Avoid injury! Children or bystanders may be injured by runover and rotating blades. Before traveling forward or rearward: Carefully check the area around the machine. Disengage the mower before backing up.
To travel forward. Push down the reverse travel pedal (B).
To stop travel: Push down brake pedal (C). Travel pedals will return to the neutral position. Using The Reverse Implement Option (RIO) c CAUTION: Avoid injury! Rotating blades are dangerous. Children or bystanders may be injured by runover and rotating blades. Before backing up, carefully check the area around the machine. NOTE: Backing up while the mower is engaged is strongly discouraged.
The Reverse Implement Option should be used ONLY when operating another attachment or when the operator deems it necessary to reposition the machine with the mower engaged. Stop forward travel. Look behind the vehicle to be sure there are no bystanders. Push and hold in the reverse implement switch (A) while depressing reverse foot pedal slightly for Automatic Transmission OR moving the gear shift lever to the R (reverse) position for Gear Transmission. NOTE: If the engine and mower stop while repositioning the machine, return the mower engagement lever to the off position. Start engine and engage mower.
Begin again with Step 2. Release the reverse implement switch and reposition the machine as the machine begins to move rearward. Resume forward travel.
The mower should continue operating. Repeat procedure to position the machine again. Using Mower Lift Lever MOWING (FORWARD) POSITION Maintains cutting height previously set. NOTE: On 38-in. Or Freedom42: Lift lever must be locked into the lower position to avoid uneven cutting.
This position allows deck to float over uneven terrain. On 48C: Use when mowing in extremely rough terrain. Mower is locked in lowest position.
Pull lift lever (A) back slightly. IMPORTANT: Avoid damage! Transmission damage may occur if the machine is moved or towed incorrectly: Move unit by hand only.
Do not use another vehicle to move unit. Do not tow unit. Drive forward onto heavy-duty trailer.
Lower mower to trailer deck. Lock park brake. Fasten lawn tractor to trailer with heavy-duty straps, chains, or cables. Both front and rear straps must be directed down and outward from tractor. Strap down hood. Using Wheel Weights Install front wheel weights for added stability and steering control when you use equipment such as the rear-mounted grass bagger. Install rear wheel weights when using the front blade.
Remove wheel weights when not required. Installing Tire Chains. Tie excess rim chain links (G) back to the rim chain. Drive forward on chains 9-12 m (30-40 ft.) and recheck for tightness.
Adjust as necessary. Mowing Tips The following recommendations will produce the best lawn cut quality and appearance: Keep mower blades sharp. Dull blades will tear grass; tips of grass will then turn brown. Cutting grass too short may kill grass and let weeds grow easily. The suggested finished cut height range is 44 to 70 mm (1.75 to 2.75 in.). Adjust cutting height to remove only 1/3 of the grass at a time.
When using the Freedom42 Mulching Mower: Shorter cut heights will provide better cut quality, but may leave noticeable clippings. Higher cut heights will reduce clippings, but cut quality may decline. Do not mow wet grass. Wet cutting conditions will not adversely affect the cutting performance of the Freedom42 Mulching Mower. Mow grass often.
Short grass clippings will decay quickly. Mow with engine at full throttle. Adjust travel speed to match mowing conditions: Travel at SLOW speed when you mow thick, tall grass, make sharp turns or trim around objects. Travel at MODERATE speed when you mow thin grass. Use a different mowing pattern each time you mow.
Overlap mowing paths 50 to 100 mm (2 to 4 in.). Drive over ridges and through shallow ditches straight-on, not at an angle.
Operating OMM142698 Issue I0 Lawn Tractors LT133, LT155 and LT166 PIN (125001 - ) Copyright© Deere & Company Operating Daily Operating Checklist o Test safety systems. O Check tire pressure.
O Check fuel level. O Check engine oil level. O Remove grass and debris from machine.
O Clean air intake screen. O Check area below machine for leaks. Avoid Damage to Plastic and Painted Surfaces Do not wipe plastic parts unless rinsed first. Insect repellent spray may damage plastic and painted surfaces. Do not spray insect repellent near machine. Be careful not to spill fuel on machine. Fuel may damage surface.
Wipe up spilled fuel immediately. Operator Station Controls. M63896 Install both springs into front position (C) for softest ride. Install both springs into rear position (B) for firm ride. Install springs in all four positions (B and C) for the firmest ride.
NOTE: Installing all four springs is also recommended for use with the Optional High-Back Seat. Additional springs and the high-back seat are available at your John Deere dealer. Adjusting Cutting Height NOTE: Lift lever should be in transport position before turning cutting height knob. Cutting height can be adjusted from approximately 25-100 mm (1-4 in). When lift lever is in transport position, cutting height is approximately 100 mm (4 in).
Put lift lever in transport position. 48C: 37 Nm (27 lb-ft.) (328 lb-in.) Adjusting Mower Level (Side-to-Side) c CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. Always wear gloves when handling mower blades or working near blades. NOTE: Mower wheels should not contact the ground when leveling the deck.
Park machine safely on a level surface. Inflate tires to the correct pressure. Adjust cutting height to 50 mm (2 in).
Put lift lever in mowing position. NOTE: The difference between blade measurements must not be more than 3 mm (1/8 in).
MIF Picture Note: Left side shown. Adjust lift links by turning nut (G) clockwise to raise left side of mower, counterclockwise to lower left side of mower. Adjusting Mower Level (Front-to-Rear) c CAUTION: Avoid injury! Rotating blades are dangerous. Before adjusting or servicing mower: Disconnect spark plug wire(s) to prevent engine from starting accidently. Always wear gloves when handling mower blades or working near blades.
NOTE: Mower wheels should not contact the ground during leveling. Park machine safely on a level surface. Inflate tires to the correct pressure. Adjust cutting height to 50 mm (2 in). Put lift lever in mowing position.
Turn right blade so blade tip points straight forward. MIF c CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death. Move the vehicle to an outside area before running the engine. Do not run an engine in an enclosed area without adequate ventilation.
Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area. Allow fresh outside air into the work area to clear the exhaust fumes out. Use the following checkout procedure to check for normal operation of machine.
If there is a malfunction during one of these procedures, Do not operate machine. See your John Deere dealer for service.
Perform these tests in a clear open area. Keep bystanders away.
Testing Mower Engagement Lever Switch 1. Sit on the seat. Lock the park brake. Result: Park brake must prevent machine from moving. If machine moves, parking brake needs to be adjusted.
John Deere 125 Mower Manual
Testing Reverse Implement Option (RIO) 1. Start engine. Engage mower. C CAUTION: Avoid injury! Rotating blades are dangerous. Children or bystanders may be injured by runover and rotating blades.
Before backing up, carefully check the area around the machine. Look behind the vehicle to be sure there are no bystanders. Begin reverse travel by depressing reverse foot pedal for Automatic transmission or moving gear shift lever to R (reverse) position for Gear transmission. Push and hold brake pedal (A) down. Pull park brake lever (B) up to lock park brake. Release brake pedal. Pedal should stay down and park brake lever should stay locked.
Unlocking park brake: 1. Push and hold brake pedal down. Push park brake lever down to unlock park brake. Release brake pedal. Starting Engine c CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.
Move the vehicle to an outside area before running the engine. Do not run an engine in an enclosed area without adequate ventilation. Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area. Allow fresh outside air into the work area to clear the exhaust fumes out. NOTE: Engine will not start unless mower is disengaged and transmission is in neutral. Push down brake pedal. Check starting conditions.
M94336a A - STOP Position B - Headlights `ON' Position C - Run Position D - Start Position Turning Headlights ON/OFF (Engine OFF) ON - Turn key switch to headlights `ON' position (B) - lights will turn on. However, this will drain the battery rapidly, so do not leave headlights on for periods longer than 1 - 2 minutes.
OFF - Turn key switch to STOP position (A) - lights will turn off. Turning Headlights ON/OFF (Engine RUNNING) ON - Start engine, then turn key switch from run position (C) to headlights `ON' position (B) - lights will turn on. OFF - Turn key switch from headlights position (B): to run position (C) - lights will turn off and engine will continue to run. To STOP position (A) - lights and engine will turn off.
Using Travel Controls on Gear Transmission c CAUTION: Avoid injury! Children or bystanders may be injured by runover and rotating blades.
Before traveling forward or rearward: Carefully check the area around the machine. Disengage the mower before backing up. Push clutch/brake pedal (A) all the way down. NOTE: The engine and mower will stop as the gear shift lever is moved to R (reverse) if the mower engagement lever is not in the off position. Put mower engagement lever (C) in the off position.
Look behind the vehicle to be sure there are no bystanders nearby. Move shift lever (B) to R (reverse) position. Release clutch/brake pedal slowly. To stop travel: Push down clutch/brake pedal. Using Travel Pedals on Automatic Transmission c CAUTION: Avoid injury! Children or bystanders may be injured by runover and rotating blades.
Before traveling forward or rearward: Carefully check the area around the machine. Disengage the mower before backing up. To travel forward.
Push down the reverse travel pedal (B). To stop travel: Push down brake pedal (C). Travel pedals will return to the neutral position. Using The Reverse Implement Option (RIO) c CAUTION: Avoid injury! Rotating blades are dangerous. Children or bystanders may be injured by runover and rotating blades. Before backing up, carefully check the area around the machine.
NOTE: Backing up while the mower is engaged is strongly discouraged. The Reverse Implement Option should be used ONLY when operating another attachment or when the operator deems it necessary to reposition the machine with the mower engaged. Stop forward travel. Look behind the vehicle to be sure there are no bystanders. Push and hold in the reverse implement switch (A) while depressing reverse foot pedal slightly for Automatic Transmission OR moving the gear shift lever to the R (reverse) position for Gear Transmission. NOTE: If the engine and mower stop while repositioning the machine, return the mower engagement lever to the off position. Start engine and engage mower.
Begin again with Step 2. Release the reverse implement switch and reposition the machine as the machine begins to move rearward. Resume forward travel. The mower should continue operating. Repeat procedure to position the machine again. Using Mower Lift Lever MOWING (FORWARD) POSITION Maintains cutting height previously set.
NOTE: On 38-in. Or Freedom42: Lift lever must be locked into the lower position to avoid uneven cutting. This position allows deck to float over uneven terrain. On 48C: Use when mowing in extremely rough terrain. Mower is locked in lowest position.
Pull lift lever (A) back slightly. IMPORTANT: Avoid damage! Transmission damage may occur if the machine is moved or towed incorrectly: Move unit by hand only. Do not use another vehicle to move unit. Do not tow unit. Drive forward onto heavy-duty trailer.
Lower mower to trailer deck. Lock park brake. Fasten lawn tractor to trailer with heavy-duty straps, chains, or cables.
John Deere 125 Owners Manual
Both front and rear straps must be directed down and outward from tractor. Strap down hood.
Using Wheel Weights Install front wheel weights for added stability and steering control when you use equipment such as the rear-mounted grass bagger. Install rear wheel weights when using the front blade. Remove wheel weights when not required. Installing Tire Chains. Tie excess rim chain links (G) back to the rim chain. Drive forward on chains 9-12 m (30-40 ft.) and recheck for tightness.
Adjust as necessary. Mowing Tips The following recommendations will produce the best lawn cut quality and appearance: Keep mower blades sharp. Dull blades will tear grass; tips of grass will then turn brown. Cutting grass too short may kill grass and let weeds grow easily.
The suggested finished cut height range is 44 to 70 mm (1.75 to 2.75 in.). Adjust cutting height to remove only 1/3 of the grass at a time.
When using the Freedom42 Mulching Mower: Shorter cut heights will provide better cut quality, but may leave noticeable clippings. Higher cut heights will reduce clippings, but cut quality may decline. Do not mow wet grass. Wet cutting conditions will not adversely affect the cutting performance of the Freedom42 Mulching Mower. Mow grass often. Short grass clippings will decay quickly.
Mow with engine at full throttle. Adjust travel speed to match mowing conditions: Travel at SLOW speed when you mow thick, tall grass, make sharp turns or trim around objects.
Travel at MODERATE speed when you mow thin grass. Use a different mowing pattern each time you mow. Overlap mowing paths 50 to 100 mm (2 to 4 in.).
Drive over ridges and through shallow ditches straight-on, not at an angle.